2020 Maintainer (2-ton ENPAK)

 

Expected in stock April 2021

Maintainer Service Body Model H10025ST-2-120 (EnPak)

Mounted on a Kenworth T370 Chassis

 

QTY

DESCRIPTION

 

--------  Maintainer Body  --------

1

MTS-2-120, 62" High X 23" Deep Compartments, 14' Long Body, 12-gauge body with 11-gauge deck-plate compartment tops & backs, 54" x 31" wheel well opening. 

Galvanneal body includes Cabinets with reinforced floors, clean out drains and adjustable aluminum shelving package (250 lb. capacity),

3/16" Aluminum doors with Three Point D-ring door latches and gas spring door holders, 49"W center deck floor is 1/8" diamond plate. 

Also includes wheel skirting, front body bulkhead, rear 10" tall hinge down tailgate, mud flaps, rear body grab handles,

ICC recessed LED lights & reflectors, includes 2 rear oval strobes (Buyers SL66CA)

97dB backup alarm, and Mini I.C.C. safety kit (2.5 lb ABC fire extinguisher & hazard reflectors).

Body primed and undercoated, splatter-coating on compartment interiors.

1

Short Tower Crane reinforcement for MTS 1 or 2 ton service body (up to 75,000 ft*lb)

NOTE: For individual crane equip. & accessory items ie. adj. boom saddle, outrigger pkgs., body leveling pkgs., hyd. pkgs. to operate a crane or other hyd. drive components-Contact Factory

1

Single compartment in lieu of 2 standard compartments NOTE: For up to 59" wide compartment.

(2) 45" wide front SS compartments in lieu of (3) compartments

1

Factory Installation of body on a chassis

     

    

 

--------  Compartment Equipment & Accessories  --------

1

Pressurized Storage System (PSS), 2-blowers with filters

1

Oxy / Act bottle storage w/ratchet strap, vents, "J" hks. & reinforced floor

14

Feet of Master Compartment Locking System for steel body. Spring loaded with padlock guards for both side packs

     


 

--------  Hydraulic Power Package  --------

1

Miller EnPak A60HGE (Diesel) Power Package with control panel

  24.8HP Kubota diesel engine, utilizes chassis 12-volt battery & fuel (requires two auxiliary fuel ports)

  Includes engine block heater with 120V plug-in

  Crane remote integration: Not Included / Quoted separately

  Hydraulic Pump: Closed Center /Load Sensing (10 gpm), Includes hydraulic reservoir w/ 120V heater & 3-way switch

  Air Compressor: Rotary screw 60 CFM @ 100 PSI (Air tank required, quoted separately)

  Generator: 6000 Watt, GFI outlets (1) 120V, (1) 240V Remote-mounted

  Welder: Not Included, See Maxstar welder options

  Inverter: EnVerter - 2400 Watt, with (1) 120V GFI outlet

  Jumpstart / Charger: Not included / quoted separately

  White housing; 21"W x 30"T x 47"L, 832 lbs

Note: Specify mounting location:

      -Center deck location may require a removable panel for protection

      -If mounted near fixed walls, requires a minimum of 36" width for air flow and panel access

      -If inside an enclosure, requires AO-03606 for ventilation

1

Air tank - 17 gallon - Pressure rating of 200 psi / 16" diameter - painted black (000012)

Includes moisture drain

1

Crane remote control hook-up (tethered or wireless), for engine-driven power packages

1

Mounting angles

1

Bolt-On Riser / Skid (no tank) for engine driven power units / APU's in lieu of mounting angles

Provides better air flow and/or storage underneath, Includes mount for hydraulic reservoir

1

Heater, electric, for chassis cab. 120 volt, fan forced, 1,000 / 1,500 watt (014892) - w/ male plug

NOTE: May require an additional 120 volt plug-in wired to power source

     

     

 

--------  Crane Equipment & Accessories  --------

1

H10025ST Crane 10,000 lb max capacity (75,000 ft*lb) with hydraulic extend hex-boom 13'-25'

Crane includes a true independent, proportional wireless remote, holder with storage sensor & indicator light,

ACC w/ crane lifting weight display, planetary winch, crane hour meter, engine start/stop, A2B, overload system,

holding valves & load block with non-live-swivel safety hook.

Note: Maximum pedestal height = 31"

Paint note:

Ship-out crane-only: Requires additional paint charge

Crane installed on body: No additional paint charge unless different color than body

1

Install hydraulic crane on body - includes boom saddle, and valve well with HD reinforced cover

1

Annual crane inspection (Initial inspection)

     

     

 

--------  Outriggers & Accessories  --------

1

Outriggers for cranes up to 75,000 ft*lb, hydraulic up/down rear outriggers (2) with hydraulic extend in/out on crane side (48" extend)

     

    

 

--------  Chassis Equipment & Accessories  --------

1

~Camera, NagyFleet, 7" Color monitor, external mount camera with infra-red

Note: Monitor mounted to windshield (not on dash)

     

     

 

--------  Air Compressor Equipment & Accessories  --------

1

Hose reel access (fiber box)

1

Air accessory package - 1/2" X 50' Filter / lubricator / regulator, spring rewind reel 022671 (J spring), hose & ball stop

     

     

 

--------  Lighting / Electrical Equipment & Accessories  --------

1

~Exterior 12v LED flood light pkg. 1-perm 022232 / 1-remote 022233 (2,100 lumens)

4

~Exterior 12v LED flood light 022232 (2,100 lumens)

10

Interior 12 v. LED strip light (can be used in O/A compartments)

1

~Strobe Lightheads Low profile L.E.D, rectangular, amber, external mount, Whelen TIR3  3.5" x 1.13" (2x-1 ea front corner) . Chassis Front.

012002 for vertical mount applications / 012513 for horizontal mount applications

1

~Exterior 12v LED flood light (1,550 lumens) on crane boom tip (2-Lights) on pivot bracket (024261)

1

~Light Bar Mount (Aluminum), front of body, center deck width, tube frame, no panel

Includes paint or protective spray coating to match body layout

1

Light bar mounting plate, includes wire loom holders

1

~Light Bar, Whelen amber Lo-Profile LED mini light bar, Model MC16PA (#019873)

2-3/8"H x 16-1/2"W x 7-3/4"D, installed with switch in cab 

Note: Mounting plate not included

1

Sealed duplex electrical GFI outlet, 120 volt, Installed & wired to power source. Chassis cab – for heater.

     

    

 

--------  Painting Equipment & Accessories  --------

14

Feet of unit painted urethane "White" color. Not a base coat/clear coat or Metallic  

Note: Includes protective spray covering on compartment fronts, bottom door frames, outside area around wheel wells, outer vertical outrigger tubes, rear bumper face & step surface

Note: Due to variations in OEM paint products and application methods, Maintainer cannot guarantee a perfect paint match on color

Note: For colors other than white additional charges will be required

14

Feet of Protective Spray Covering - MTS - cargo center deck, compartment tops & sides, front bulkhead, tail gate & extension, bumper and/or workbench area

     

     

 

--------  Roll-Out drawer and Tray Equipment & Accessories  --------

1

~DuaLock (5) drawer aluminum set 18"W x 18"D x (5)-4"H, (300 lb. cap. per drawer) Includes top shelf

7" bottom space, overall height 30", #013225, Installed. SS rear.

(1) Permanent Front-to-Back divider, (4) Removable Side-to-Side Dividers

1

DuaLock custom drawer aluminum set (300 lb. cap. Ea.) Includes top shelf.

39"W x 18"D

(1) 7" H, (3) -5"H, (3)  -3" H Drawers

Location: SS 1st

Permanent & Removable Dividers will be provided but configurations vary depending on drawer width and depth

Note: Requires installation charge if applicable, specify drawer details.

1

Install charge for mounting drawer set (DuaLock, etc) in Maintainer compartment (EACH)

    

     

 

--------  Center Deck Equipment & Accessories  --------

6

Flush mount "D" ring tie-downs in bed floor #003217, each

     

   

 

--------  Rear Bumper & Accessories  --------

1

26" steel workbench bumper with recessed step on one side, 2 side storage compartments

Includes a single mounting pocket for an optional vise / grinder mounting plate

Includes: 2 grab handles and strip light for recessed step safety, transverse bar storage (75" long, flush with floor), doors on both sides.

Includes a stainless steel rear bumper shell

Note: Hitch and trailer plug to be quoted separately

1

Class IV hitch receiver - 2" receiver - rated at 1,500 lbs. vert.  10,000 lbs. MGTW 

Note: customer is responsible to verify tow rating of chassis and available GVWR/GCWR remaining after loading of body and all other items.

1

Trailer plug-in 7-prong flat blade #007486 (RV style)

    

    

 

--------  Miscellaneous Equipment & Accessories  --------

1

Vise / grinder removable mounting plate HD, includes drain slots in plate

1

Single axle wheel well extensions (3-piece bolt-on),aluminum w/ protective spray.

Note: Kit includes flares for both sides of body

Expected in stock April 2021

Maintainer Service Body Model H10025ST-2-120 (EnPak)

Mounted on a Kenworth T370 Chassis

 

QTY

DESCRIPTION

 

--------  Maintainer Body  --------

1

MTS-2-120, 62" High X 23" Deep Compartments, 14' Long Body, 12-gauge body with 11-gauge deck-plate compartment tops & backs, 54" x 31" wheel well opening. 

Galvanneal body includes Cabinets with reinforced floors, clean out drains and adjustable aluminum shelving package (250 lb. capacity),

3/16" Aluminum doors with Three Point D-ring door latches and gas spring door holders, 49"W center deck floor is 1/8" diamond plate. 

Also includes wheel skirting, front body bulkhead, rear 10" tall hinge down tailgate, mud flaps, rear body grab handles,

ICC recessed LED lights & reflectors, includes 2 rear oval strobes (Buyers SL66CA)

97dB backup alarm, and Mini I.C.C. safety kit (2.5 lb ABC fire extinguisher & hazard reflectors).

Body primed and undercoated, splatter-coating on compartment interiors.

1

Short Tower Crane reinforcement for MTS 1 or 2 ton service body (up to 75,000 ft*lb)

NOTE: For individual crane equip. & accessory items ie. adj. boom saddle, outrigger pkgs., body leveling pkgs., hyd. pkgs. to operate a crane or other hyd. drive components-Contact Factory

1

Single compartment in lieu of 2 standard compartments NOTE: For up to 59" wide compartment.

(2) 45" wide front SS compartments in lieu of (3) compartments

1

Factory Installation of body on a chassis

     

    

 

--------  Compartment Equipment & Accessories  --------

1

Pressurized Storage System (PSS), 2-blowers with filters

1

Oxy / Act bottle storage w/ratchet strap, vents, "J" hks. & reinforced floor

14

Feet of Master Compartment Locking System for steel body. Spring loaded with padlock guards for both side packs

     


 

--------  Hydraulic Power Package  --------

1

Miller EnPak A60HGE (Diesel) Power Package with control panel

  24.8HP Kubota diesel engine, utilizes chassis 12-volt battery & fuel (requires two auxiliary fuel ports)

  Includes engine block heater with 120V plug-in

  Crane remote integration: Not Included / Quoted separately

  Hydraulic Pump: Closed Center /Load Sensing (10 gpm), Includes hydraulic reservoir w/ 120V heater & 3-way switch

  Air Compressor: Rotary screw 60 CFM @ 100 PSI (Air tank required, quoted separately)

  Generator: 6000 Watt, GFI outlets (1) 120V, (1) 240V Remote-mounted

  Welder: Not Included, See Maxstar welder options

  Inverter: EnVerter - 2400 Watt, with (1) 120V GFI outlet

  Jumpstart / Charger: Not included / quoted separately

  White housing; 21"W x 30"T x 47"L, 832 lbs

Note: Specify mounting location:

      -Center deck location may require a removable panel for protection

      -If mounted near fixed walls, requires a minimum of 36" width for air flow and panel access

      -If inside an enclosure, requires AO-03606 for ventilation

1

Air tank - 17 gallon - Pressure rating of 200 psi / 16" diameter - painted black (000012)

Includes moisture drain

1

Crane remote control hook-up (tethered or wireless), for engine-driven power packages

1

Mounting angles

1

Bolt-On Riser / Skid (no tank) for engine driven power units / APU's in lieu of mounting angles

Provides better air flow and/or storage underneath, Includes mount for hydraulic reservoir

1

Heater, electric, for chassis cab. 120 volt, fan forced, 1,000 / 1,500 watt (014892) - w/ male plug

NOTE: May require an additional 120 volt plug-in wired to power source

     

     

 

--------  Crane Equipment & Accessories  --------

1

H10025ST Crane 10,000 lb max capacity (75,000 ft*lb) with hydraulic extend hex-boom 13'-25'

Crane includes a true independent, proportional wireless remote, holder with storage sensor & indicator light,

ACC w/ crane lifting weight display, planetary winch, crane hour meter, engine start/stop, A2B, overload system,

holding valves & load block with non-live-swivel safety hook.

Note: Maximum pedestal height = 31"

Paint note:

Ship-out crane-only: Requires additional paint charge

Crane installed on body: No additional paint charge unless different color than body

1

Install hydraulic crane on body - includes boom saddle, and valve well with HD reinforced cover

1

Annual crane inspection (Initial inspection)

     

     

 

--------  Outriggers & Accessories  --------

1

Outriggers for cranes up to 75,000 ft*lb, hydraulic up/down rear outriggers (2) with hydraulic extend in/out on crane side (48" extend)

     

    

 

--------  Chassis Equipment & Accessories  --------

1

~Camera, NagyFleet, 7" Color monitor, external mount camera with infra-red

Note: Monitor mounted to windshield (not on dash)

     

     

 

--------  Air Compressor Equipment & Accessories  --------

1

Hose reel access (fiber box)

1

Air accessory package - 1/2" X 50' Filter / lubricator / regulator, spring rewind reel 022671 (J spring), hose & ball stop

     

     

 

--------  Lighting / Electrical Equipment & Accessories  --------

1

~Exterior 12v LED flood light pkg. 1-perm 022232 / 1-remote 022233 (2,100 lumens)

4

~Exterior 12v LED flood light 022232 (2,100 lumens)

10

Interior 12 v. LED strip light (can be used in O/A compartments)

1

~Strobe Lightheads Low profile L.E.D, rectangular, amber, external mount, Whelen TIR3  3.5" x 1.13" (2x-1 ea front corner) . Chassis Front.

012002 for vertical mount applications / 012513 for horizontal mount applications

1

~Exterior 12v LED flood light (1,550 lumens) on crane boom tip (2-Lights) on pivot bracket (024261)

1

~Light Bar Mount (Aluminum), front of body, center deck width, tube frame, no panel

Includes paint or protective spray coating to match body layout

1

Light bar mounting plate, includes wire loom holders

1

~Light Bar, Whelen amber Lo-Profile LED mini light bar, Model MC16PA (#019873)

2-3/8"H x 16-1/2"W x 7-3/4"D, installed with switch in cab 

Note: Mounting plate not included

1

Sealed duplex electrical GFI outlet, 120 volt, Installed & wired to power source. Chassis cab – for heater.

     

    

 

--------  Painting Equipment & Accessories  --------

14

Feet of unit painted urethane "White" color. Not a base coat/clear coat or Metallic  

Note: Includes protective spray covering on compartment fronts, bottom door frames, outside area around wheel wells, outer vertical outrigger tubes, rear bumper face & step surface

Note: Due to variations in OEM paint products and application methods, Maintainer cannot guarantee a perfect paint match on color

Note: For colors other than white additional charges will be required

14

Feet of Protective Spray Covering - MTS - cargo center deck, compartment tops & sides, front bulkhead, tail gate & extension, bumper and/or workbench area

     

     

 

--------  Roll-Out drawer and Tray Equipment & Accessories  --------

1

~DuaLock (5) drawer aluminum set 18"W x 18"D x (5)-4"H, (300 lb. cap. per drawer) Includes top shelf

7" bottom space, overall height 30", #013225, Installed. SS rear.

(1) Permanent Front-to-Back divider, (4) Removable Side-to-Side Dividers

1

DuaLock custom drawer aluminum set (300 lb. cap. Ea.) Includes top shelf.

39"W x 18"D

(1) 7" H, (3) -5"H, (3)  -3" H Drawers

Location: SS 1st

Permanent & Removable Dividers will be provided but configurations vary depending on drawer width and depth

Note: Requires installation charge if applicable, specify drawer details.

1

Install charge for mounting drawer set (DuaLock, etc) in Maintainer compartment (EACH)

    

     

 

--------  Center Deck Equipment & Accessories  --------

6

Flush mount "D" ring tie-downs in bed floor #003217, each

     

   

 

--------  Rear Bumper & Accessories  --------

1

26" steel workbench bumper with recessed step on one side, 2 side storage compartments

Includes a single mounting pocket for an optional vise / grinder mounting plate

Includes: 2 grab handles and strip light for recessed step safety, transverse bar storage (75" long, flush with floor), doors on both sides.

Includes a stainless steel rear bumper shell

Note: Hitch and trailer plug to be quoted separately

1

Class IV hitch receiver - 2" receiver - rated at 1,500 lbs. vert.  10,000 lbs. MGTW 

Note: customer is responsible to verify tow rating of chassis and available GVWR/GCWR remaining after loading of body and all other items.

1

Trailer plug-in 7-prong flat blade #007486 (RV style)

    

    

 

--------  Miscellaneous Equipment & Accessories  --------

1

Vise / grinder removable mounting plate HD, includes drain slots in plate

1

Single axle wheel well extensions (3-piece bolt-on),aluminum w/ protective spray.

Note: Kit includes flares for both sides of body